Can I Set Up A Tub Myself?
Can I Set Up A Tub Myself?
Blog Article
Nearly everybody is bound to have their unique opinion involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a tub isn't specifically rocket science, yet it does call for solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bathtub with a new one is also a moderately tough job. If the old bathtub is conveniently accessible, the job can relocate easily; if you have to open up a wall to remove the old tub as well as place the brand-new bath tub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Make certain you have actually certified on your own for the work and also are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This article will help you install a new bath tub in your bathroom if you have actually currently acquired a brand-new bathtub and also do not need to change the setup of your previous water supply pipelines.
Your devices as well as material checklist ought to comprise the following:
Preparing for the Installation
To start with, the sustaining structure supplied with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the tap comes with a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to prevent pressure on the tub.
Fit the flexible tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be rather problematic because of the limited gain access to that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly come from the pipes. Once the supply pipelines have actually been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the needed placement. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be accomplished by examining the level and also adjusting the feet on the bathtub until the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest flexible tap connector to the ideal supply pipe by making a compression join; then do the same for the other tap.
Turn on the water system as well as inspect all joints and also brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the tub must wait up until the tub has been utilized at least once as this will settle it into its last placement.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers are in place between the tap as well as the sink. Protect the tap in position with the maker supplied backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous type ought to be linked to the tap ends first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to crack a rigid seal, creating the water to pass through the wall surface in between the bath and the tiling, leading to complications with wetness as well as possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and cartridges, as well as are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealer can crack rather early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently available on the marketplace. It is suggested to fit the tiles making use of waterproof or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been introduced to that report about Installing A Bathtub through an acquaintance on our other domain. Are you aware of another person who is occupied with the topic? Do not hesitate to promote it. Many thanks for your time invested reading it.
Book Today!
Report this page